
{{ variable.name }}
An 8,000 kg straight-boom crane truck on a 4x2 chassis with 13.5 m maximum lifting height and 11.5 m maximum working radius, plus a 5,400-5,550 x 2,294 x 600 mm drop-side cargo body built around the crane position.
The straight (telescopic) boom gives the higher vertical lift of the two boom families: up to 13.5 m lifting height and 11.5 m working radius on this 8,000 kg crane truck. The boom runs on 2-5 hydraulic extensions with a fly jib optional, and the drop-side body on the quoted straight-arm unit measures 5,400-5,550 x 2,294 x 600 mm. Capacity is always quoted together with the radius, and the load chart ships with the unit.


Straight Boom Reaches Higher
13.5 m maximum lifting height and 11.5 m maximum working radius, with 2-5 hydraulic boom extensions and the load lowered on a rope rather than carried on a knuckle.
Capacity Quoted With The Radius
The load chart ships with every unit and the lift is checked from the actual radius and boom length, so the shortest-radius figure is not used to plan the job.
Cargo Body Built Around The Crane
5,400-5,550 x 2,294 x 600 mm drop-side body with removable posts, rope hooks and lashing points; body length is fixed to the crane position so the boom never fouls the load.
Payload Budget Settled Before The Order
GVW 12,005-16,000 kg and curb weight 5,880-6,050 kg with crane, subframe and body, so GVW, rear-axle load and the remaining cargo capacity are confirmed before the chassis is specified.
Outriggers Sized For Real Sites
Box-section H-type front and rear legs, 2.2-5.5 m lateral spread across the range, with full and partial spread quoted as separate capacity columns.
Hydraulics Chosen For Service Markets
Open-centre system at 16-35 MPa on a gearbox power take-off, hard-chrome cylinder rods, and seal kits and hoses shipped as a spare-parts kit.
| Parameter | Specification |
| Crane type | Straight (telescopic) boom, truck-mounted |
| Rated capacity | 8,000 kg |
| Max working radius | 11.5 m |
| Max lifting height | 13.5 m |
| Boom sections | 2-5 hydraulic extensions, fly jib optional |
| Lifting moment across the range | 8-60 tonne-metres, quoted as load multiplied by radius |
| Outriggers | Hydraulic H-type front and rear legs, box section, 2.2-5.5 m spread, full and partial |
| Controls | Manual lever bank at the crane base; proportional radio remote control optional |
| Hydraulics | Open centre, gearbox power take-off, 16-35 MPa |
| Chassis and wheelbase | 4x2, 4,700-5,000 mm |
| GVW and curb weight | 12,005-16,000 kg / 5,880-6,050 kg with crane, subframe and body |
| Overall dimensions | 8,600-9,000 x 2,500 x 3,200-3,650 mm |
| Engine and transmission | Diesel 132-180 hp (97-132 kW), 4.5-5.9 L, Euro II to Euro V; manual 6-speed |
| Brakes and tyres | Air brake with ABS, exhaust brake, spring parking brake; 9.00R20, 6 tyres plus one spare |
| Cargo body | 5,400-5,550 x 2,294 x 600 mm drop side, 3-5 mm steel or checker plate floor |
| Max speed | 90-100 km/h |
Boom, column and knuckle joints are welded high-strength steel box section in Q345 or Q460 plate, reinforced with Q345 plates at the pivot points. The subframe is Q345 channel or box section, bolted and welded to the chassis rails, and the cargo body is Q235/Q345 steel with a 3-5 mm floor plate and double-wall drop sides.
Boom sections, fly jib, crane position, body length and chassis class are fixed before the order, from the heaviest load, the longest radius, the site access and ground, the cargo carried and the local rules on lifting equipment. A rear-mounted crane on a longer body is offered where the load has to be placed behind the truck, and radio remote control, air suspension and hub reduction are selected at the same stage.
A construction contractor and equipment rental operator in the Philippines received one complete crane truck with a duty-matched configuration. The unit was installed in September 2025 with on-site assembly and commissioning; after about 14 months in service the recorded result is good performance, reliability and site adaptability, with the client reported as highly satisfied.

How high and how far does the boom reach?
13.5 m maximum lifting height and 11.5 m maximum working radius on this unit, with 3-16 m working radius available across the range.
What capacity can I plan on?
Capacity is quoted with the radius. The load chart ships with the unit and the lift is planned from the actual radius and boom length, not from the rating alone.
What cargo body is fitted?
A 5,400-5,550 x 2,294 x 600 mm drop-side body on the quoted straight-arm unit, with a 3-5 mm steel or checker plate floor, removable posts and lashing points; 3-9 m body length is available.
Which chassis do I need for a larger crane?
6x4 covers 8,000-16,000 kg cranes and 8x4 covers 16,000-25,000 kg, with GVW 18,000-31,000 kg and wheelbase 5,700-7,500 mm on those configurations.
What controls and safety devices are available?
A manual lever bank at the crane base is standard and proportional radio remote control is optional. A load moment limiter is available for the lifting circuit, with pressure relief and check valves and an alarm when an outrigger is not fully deployed.
Lead time, warranty and shipping terms?
About 30-45 working days from down payment and a 12-month warranty on major components. Units ship by RoRo or container under FOB, CIF or DAP terms with invoice, packing list, bill of lading, certificate of origin and insurance.
Share the heaviest load, the longest radius, the site access and ground, the cargo carried and the local rules on lifting equipment. Sales engineers confirm boom type, crane class, chassis, crane position and body length before the order.
Henan Elorry Industrial Co., Ltd. | Tel +86-13083602803 | WhatsApp +86-16638078903 | info@elorry-ind.com | Zhengzhou City, Henan Province, China
Hydraulic seal kits, hoses, filters and control valves are supplied as a spare-parts kit with the unit.