
{{ variable.name }}
A 4,000 kg knuckle boom crane truck that carries its own load to site and lifts it without a second machine or a hired mobile crane. The folding boom stows inside the vehicle width behind the cab, so the cargo bed stays clear.
This crane truck pairs a 4,000 kg folding boom with a 20 tonne-metre lifting moment on a 4x2 commercial chassis. Capacity is quoted with the radius: about 3,300 kg at 6 m and about 2,400 kg at 7.8 m, with a maximum working radius of 7.815 m and a maximum lifting height of 10 m. GVW on the quoted 4x2 unit is 12,005-16,000 kg and curb weight is 5,880-6,050 kg with the crane, subframe and body fitted.


Bed Stays Clear With A Folding Boom
The knuckle boom stows inside the vehicle width behind the cab, so one truck delivers the load and lifts it and the body behind the crane is not taken up.
Capacity Read At The Radius That Applies
20 tonne-metre lifting moment: about 3,300 kg at 6 m and about 2,400 kg at 7.8 m. The load chart ships with the unit and the lift is checked from the actual radius and boom length.
Outriggers Sized For Real Sites
Box-section H-type front and rear legs with full and partial spread, 2.2-5.5 m lateral across the range, each spread quoted as its own capacity column for kerbsides and narrow lanes.
Hydraulics A Local Workshop Can Service
Open-centre system at 16-35 MPa on a gearbox power take-off, hard-chrome plated piston rods, and seal kits and hoses shipped as a spare-parts kit.
4x2 Chassis Matched To The Crane
132-180 hp diesel, 4.5-5.9 L, Euro II to Euro V matched to local fuel, 6-speed manual, 6,000 kg front and 10,000 kg rear axles, air brake with ABS.
Safety On The Lifting Circuit
Load moment limiter available, pressure relief and check valves, and an alarm that sounds when an outrigger is not fully deployed.
| Parameter | Specification |
| Crane type | Folding (knuckle) boom, mounted behind the cab |
| Rated capacity | 4,000 kg |
| Lifting moment | 20 tonne-metres |
| Capacity at radius | About 3,300 kg at 6 m; about 2,400 kg at 7.8 m |
| Max working radius | 7.815 m |
| Max lifting height | 10 m |
| Crane self-weight | 1,500 kg, deducted from chassis payload before body sizing |
| Outriggers and controls | Hydraulic H-type front and rear legs, box section, 2.2-5.5 m spread full and partial; manual lever bank at the crane base, proportional radio remote optional |
| Hydraulics | Open centre, gearbox power take-off, 16-35 MPa |
| Chassis and wheelbase | 4x2, 4,700-5,000 mm |
| GVW and curb weight | 12,005-16,000 kg / 5,880-6,050 kg with crane, subframe and body |
| Overall dimensions | 8,600-9,000 x 2,500 x 3,200-3,650 mm |
| Engine and transmission | Diesel 132-180 hp (97-132 kW), 4.5-5.9 L, Euro II to Euro V; manual 6-speed |
| Brakes and tyres | Air brake with ABS, exhaust brake, spring parking brake; 9.00R20, 6 tyres plus one spare |
| Cargo body | Drop-side body, 3-9 m body length available, 3-5 mm steel or checker plate floor |
| Max speed | 90-100 km/h |
Boom, column and knuckle joints are welded high-strength steel box section in Q345 or Q460 plate, with Q345 reinforcement plates at the pivot points. The subframe is Q345 channel or box section, bolted and welded to the chassis rails.
Boom type, crane class, chassis, body length and crane position are fixed before the order. Sales engineers ask for the heaviest load, the longest radius, site access and ground, the cargo carried and the local rules on lifting equipment, then size the truck so it is not bought twice. Left- or right-hand drive, radio remote control, fly jib, air suspension and hub reduction are selected at the same stage, and crane booms and attachments can be built to a customer mounting interface and dimensions.
A construction contractor and equipment rental operator in the Philippines took one complete crane truck, configured to the lifting duty on its own sites. The unit was installed in September 2025 with on-site assembly and commissioning; at about 14 months in service the recorded result is good performance, reliability and site adaptability, and the client is reported as highly satisfied.

What can this crane actually lift?
The 4,000 kg figure is the rating; the working number comes from the load chart at the radius used, about 3,300 kg at 6 m and about 2,400 kg at 7.8 m on the 20 tonne-metre unit.
Does the folding boom take cargo space?
No. The knuckle boom stows inside the vehicle width behind the cab, so the body behind it stays clear for pallets, bricks, steel or precast units.
Can the crane work when the outriggers cannot fully spread?
Yes, on the partial-spread chart. Full and partial spread are quoted as separate capacity columns, and an alarm sounds when an outrigger is not fully deployed.
How is the payload budget calculated?
GVW is 12,005-16,000 kg and curb weight 5,880-6,050 kg with crane, subframe and body. The 1,500 kg crane self-weight on the quoted unit is deducted from the chassis payload before the body is sized.
What are the lead time and warranty terms?
About 30-45 working days from down payment, with a 12-month warranty on major components; hydraulic valves and cylinders are covered under supplier terms.
How is the unit shipped?
By RoRo or container depending on unit height, under FOB, CIF or DAP terms. Invoice, packing list, bill of lading, certificate of origin and insurance are prepared together, and the hydraulic system is drained and protected for the sea passage.
Send the heaviest load, the longest radius, the site access and ground, the cargo carried and the local rules on lifting equipment. Sales engineers reply with the boom type, crane class, chassis and body length that fit the duty.
Henan Elorry Industrial Co., Ltd. | Tel +86-13083602803 | WhatsApp +86-16638078903 | info@elorry-ind.com | Zhengzhou City, Henan Province, China
Hydraulic spare-parts kit, export documents and optional radio remote control are quoted with each unit.